deskthority

Ooh I like this, any way to commit if you hit a certain price point?

skiwithpete wrote: Just posted this over on reddit to try to help generate a bit more interest.

I hope others will see in it what I do.

thanks! your post brought me over. i'm in for a set

Just shot you a PM. Will definitely commit if we can get the $30 mark.

I'd commit at $30.

I just noticed this but are there holes for the two leds that the phantom allows you to use for caps and scroll lock?

I commit at $30 too.

infamouslife7314 wrote: I just noticed this but are there holes for the two leds that the phantom allows you to use for caps and scroll lock?

No, but you can use in-switch LEDs.

Cucumberino wrote: I commit at $30 too.

Please PM me.

I'm in for qty 1 ANSI for sure - qty 2 ANSI if we hit $30/set mark

Ok! we are at 36 plates! Each person counts as 2 plates, and if we get to $30, a few people are buying 2 plates

Thanks! Keep going!

wafflepc wrote: Ok! we are at 36 plates! Each person counts as 2 plates, and if we get to $30, a few people are buying 2 plates

Thanks! Keep going!

Great news!!!

Has anyone posted this on GH?

skiwithpete wrote:

wafflepc wrote: Ok! we are at 36 plates! Each person counts as 2 plates, and if we get to $30, a few people are buying 2 plates

Thanks! Keep going!

Great news!!!

Has anyone posted this on GH?

I haven't been keeping the gh post up to date... I'll do that now. Thanks for the reminder!

skiwithpete wrote:

wafflepc wrote: Ok! we are at 36 plates! Each person counts as 2 plates, and if we get to $30, a few people are buying 2 plates

Thanks! Keep going!

Great news!!!

Has anyone posted this on GH?

LMAO JUST REMEMBERED WHY I HAVENT BEEN KEEPING IT UP TO DATE.... ITS STILL NOT UP. APPROVE PL0X

Will commit at $30.

Any updates on the count?

Can also commit at $30

We are at 48 sets! we will probably have 52 if we get to 50 sold. One more for a $30 PRICE POINT! Nice job! Ill let this run until wednesday of next week. Tommorow or Saturday i will post a notepad++ screenshot of the listings i have! If it says ??? under youre name, CONTACT ME IMMEDIATELY. If your name is not on there, CONTACT ME IMMEDIATELY.if it says possibly under your name CONTACT ME IMMEDIATELY. Thank you everyone!

http://imgur.com/1KKWfqh
The buys.

Will commit at $30 (ISO).

edit: why no three holes for spacebar?

rottencat wrote: Will commit at $30 (ISO).

edit: why no three holes for spacebar?

old render, but the new files have proper holes, and holes on the back for gonkeyboardworks feet.

EVERYONE!!! Look at the file! If there are question marks, or a possibly #, PM ME. I do NOT want to hunt you down!

This might seem like a dumb question, but where can I get the screws/bolts that are usually used for these kind of cases/plates?

Here you go!

skiwithpete wrote:

wafflepc wrote:

braidn wrote: So this doesn't come with the posts but waffle you said these were easy to find? Do you have a link where we could pick them up? Thank you.

4-40 screws, and you can use any standoffs you want. 3/8 inch works well.

like http://www.ebay.com/itm/4-40-X-1-4-SCRE ... 589b61e34c and http://www.ebay.com/itm/Raf-2057-440-B- ... 3cedbaac00

I can't figure how those post would work. do you think something like this might work as well? http://www.mcmaster.com/#93121a340/=yohe6j

Those posts have holes on both sides for the screws. As far as I can tell it would end up being kinda like the thing you linked to but I guess the problem will be that if those screws you posted fit through the case holes then they won't provide any kind of stability. The posts from my quote are bigger than the screws that fit through the hole so they stop the plates from moving.

This makes me think of a question: Are the screw holes tapered to fit a tapered head screw? Or should I be looking at pan heads?

Oh yes, got it now, they'll definitely provide more stability as you will have two screws on it. I guess an aluminum feet like the ones from gon are needed to provide a better grip to the surface or some kind of stoppers to avoid movement.

Is it possible to get the CAD files? I'd like to design an acrylic center section instead of using bolts.

keysmasher wrote: Is it possible to get the CAD files? I'd like to design an acrylic center section instead of using bolts.

Why not both? Cut an hexagonal hole through your center layers to fit the spacer into, then secure the top and bottom to the middle through those. It'd provide a very sturdy mount since the layers can't shift at all and they're being clamped from both sides.

Those McMaster binding posts linked above look like a decent solution also.

skiwithpete wrote:This makes me think of a question: Are the screw holes tapered to fit a tapered head screw? Or should I be looking at pan heads?

They are not tapered.